Jump to content

Recommended Posts

Posted

Was cruise control ever fitted to any Berlingo's would like it on my 2.0 Hdi & a retrofit would probably be easiest. If not has anybody fitted an aftermarket one with success.

 

Alan...

Posted
you should be able to fit the citroen stalk to a hdi berlingo as long as it has a comms unit. you would need to have the bsi and engine ecu configured. where are your radio controls.
Posted
you should be able to fit the citroen stalk to a hdi berlingo as long as it has a comms unit. you would need to have the bsi and engine ecu configured. where are your radio controls.

 

Sorry fr the delay in replying, didn't get an email to say you'd replied. My radio unit controls are on a stalk on the right of the steering wheel.

 

Alan...

Posted
you have a comms so you will just need to buy the stalk for the other side and then have it configured. just make sure you have a clutch switch before you start spending any money. there should be a grey 2 way multi plug on the pedal box just next to the clutch pedal going to the switch.
Posted

Once again thanks, not getting email notifications even though it's switched on & a correct address, but never mind.

 

Can this stalk come off any Citroen from what I've seen they all look the same, going dark so will look for the switch in the morning, again if there is not one there can that be taken off another Citroen & fitted, quite a few of the Picasso's & C5's have cruise control.

 

Alan...

Posted
the newer ones have a speed limiter control so you will need the older style. one from an exclusive Picasso should fit no probs but i'mm sure the stalk's are only around £30 new. you can fit a clutch switch if theres not one there but this will also need to be configured to the bsi.
Posted
If you are going to get a Citroen Dealer to do it make sure they will do it first. Citroeneddie had it done on his C3 where as mine wouldn't do it on my C2 they didn't want to get involved in it.
Posted

Been to the local Citroen dealer yesterday, stalk is older type £57+vat & they want to charge 1.5 hours @ £60 ph+vat or if I fit the stalk myself (either new or S/H) they reckon only 0.5 hours to reprogram the BSI.

 

Alan...

Posted
go for a second hand one then mate and fit it yourself. should take you no more than 10 min. 2x torx 20 screws under the cowl and it drops down and the stalk just slides into the slot. they will need to configure the engine ecu as well as the bsi so make sure they know what there doing before spending any money. did you check for a clutch switch. the main thing that goes wrong on the config is its listed as cruise control in one ecu and vvc in the other. both of these need to be activated for it to work. the bsi also needs to be left to go to sleep before the config will take effect so its no good test driving it straight after config as it wont work.
Posted

Once again thanks, checked for the switch & it's there. They have never done this at the local place, over on the C5 section they mention Lincoln Citroen have done a few. Lincoln's only 35 miles away so it might be worth fitting it & then taking a run over one day.

 

Alan...

  • 1 year later...
Posted

go for a second hand one then mate and fit it yourself. should take you no more than 10 min. 2x torx 20 screws under the cowl and it drops down and the stalk just slides into the slot. they will need to configure the engine ecu as well as the bsi so make sure they know what there doing before spending any money. did you check for a clutch switch. the main thing that goes wrong on the config is its listed as cruise control in one ecu and vvc in the other. both of these need to be activated for it to work. the bsi also needs to be left to go to sleep before the config will take effect so its no good test driving it straight after config as it wont work.

 

hi!

do you know the exact steps to configure this - preferably on a proxia cos that's what the (only) citroen dealer in Sri Lanka has?

I have a C5 (sorry this is in the wrong forum) and installed a cruise stalk (I have motorized throttle body) and managed to enable the setting in the ECU settings; but couldn't find it under the BSI settings.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...